감추기
크리스마스MCU
홈 > 센서/모듈/키트

Bearables Bear Kit [PIM319]
베어 키트 / 착용 가능한 12개의 LED가 있는 곰 뱃지 / 코딩교육용으로 적합 / 주의: 방수 및 세탁 불가
판매가격 : 17,300
적립금 :173
상품상태 :신상품
제품코드 :1361945
제조사 :pimoroni
출시일 :2018-02-12
구매수량 :
총 금액 :
MCU이용 꿀팁

2,310원
42,900원
14,300원
4,600원
3,190원
7,260원
51,150원
6,380원
503,700원
21,600원
상세정보 배송/취소/교환안내 이용후기 상품Q&A
Bearables Bear Kit [PIM319]

Kit contains

Bearables is a range of woodland-themed wearable LED badges and sensors. Wear the badges on their own, or connect them to one of the sensors with conductive thread to bring them to life. Designed for kids* (suggested age 8+) and grown-up kids alike!Attach the acorn motion sensor to the Bear badge and when you move the sensor your badge's LEDs will light up.In their five star review, The MagPi said that Bearables were "excellent value for money" and that "the badge kit has everything you need to sew your interactive badge and sensor to clothes".*Contains small parts. Not suitable for children 3 years or younger. This is not a toy. Keep battery out of reach of children. If ingested, seek medical help immediately.
  • Bear badge with 12 LEDs (multi-coloured)
  • Acorn motion sensor
  • 3m stainless steel conductive thread
  • 3 sewing needles
  • CR2032 3V coin cell battery
  • 2x sticker sheets
  • Instructions
  • Reusable box

 

Features

  • 12 coloured LEDs (blue, green, yellow, orange, red, pink)
  • 12 light patterns
  • Multi-functional button (mode change, sleep, trigger mode)
  • PIC16F1503 microcontroller
  • Sewable hooks
  • Tilt switch motion sensor
  • Battery life of 3-4 days with a CR2032 coin cell battery
Using your Bearables badge

Press the multi-functional button on your badge briefly to cycle through the light patterns. Each of the LEDs will light to indicate which of the 12 patterns is currently selected. Press and hold the button to put your badge into sleep mode.

The nifty design of the badges and sensors means that it's super-simple to connect them. It doesn't matter which way round they're connected. Just connect one hook on the badge to one hook on the sensor with conductive thread, then do the same with the other two hooks.

Once a sensor is connected, press and hold the multi-functional button to put your badge into trigger mode. Now when you trigger the sensor, the LED lights on your badge will light up.

Notes
  • Bearables badges and sensors are not waterproof or washable
  • Be aware that conductive thread is sharp!
  • Ensure that the two pieces of conductive thread connecting your Bearables badge and sensor do not touch, bearing (pun intended) in mind that they may touch when the fabric is creased or folded. Nothing bad will happen, the sensor just won't work as it should.
  • The hooks on the back can be shorted without any damage to the badge, although it may trigger the LEDs similar to triggering them with a sensor. A painted or coated safety pin will work better than a bare metal one.
  • A dab of clear nail varnish on the conductive thread around the hook can help to give a better, more reliable connection
  • Badge dimensions: 41x35x5mm (LxWxH)
  • Sensor dimensions: 25x18x4mm (LxWxH)

 

※ 공급 제조사는 재고 사정에 따라 동일 사양의 대체상품으로 공급될 수 있습니다.
※ 상기 제품에 첨부된 데이타시트는 참고사항입니다.데이타시트에 표기된 내용에 대하여 본사는 어떠한 기술적인 문의 및 발생하는 문제에 대한 법적인 책임을 지지는 않습니다. 
※ 사용자께서는 사용 전 반드시 제품에 대한 테스트 및 확인 절차 후 사용하시기 바랍니다

상세정보 배송/취소/교환안내 이용후기 상품Q&A