감추기
MCU상반기결산
홈 > 라즈베리파이

라즈베리파이 3.5인치 고해상도 터치스크린 HyperPixel - 3.5' Hi-Res Display PIM297
라즈베리파이용 고해상도 3.5' TFT 디스플레이 / 60 FPS 프레임 속도와 3.5 인치 디스플레이에서 800x480의 해상도를 제공하며 18비트 색상 표시
판매가격 : 48,000
적립금 :480
상품상태 :신상품
제품코드 :1361480
제조사 :Pimoroni
출시일 :2018-04-10
구매수량 : 품절된 상품입니다
총 금액 :
MCU이용 꿀팁

4,400원
16,900원
4,400원
36,300원
46,200원
15,400원
91,900원
95,200원
16,500원
50,000원
상세정보 배송/취소/교환안내 이용후기 상품Q&A
HyperPixel - 3.5' Hi-Res Display for Raspberry Pi [PIM297]

FEATURES

  • High-speed DPI interface
  • 3.5" display (45.3x75.6mm)
  • 800x480 pixels (~270 PPI)
  • 18-bit colour (262,144 colours)
  • 60 FPS frame rate
  • Capacitive touch
  • 40-pin female header included to boost height for Pi B+, 2, 3
  • Compatible with Raspberry Pi 3, 2, B+, A+, Zero, and Zero W
  • One-line installer

HyperPixel uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays use. It has a 60 FPS frame rate and a resolution of approximately 270 pixels per inch (800x480) on its 3.5" display. The display can show 18-bits of colour (262,144 colours).

It has a capacitive touch display that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi-touch!

Everything comes fully-assembled, and there's no soldering required! The display is securely stuck down to the HyperPixel PCB and connected via a neat little flush-mounting FPC cable. Just pop HyperPixel on your Pi and run our installer to get everything set up!

Please note: when installing HyperPixel onto your Pi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header).

It'll work with any 40-pin version of the Pi, including Pi Zero and Pi Zero W. If you're using it with a larger Pi like the B+, 2, or 3, then use the extra 40-pin header that's included to boost it up to the required height. If you're using a Zero or Zero W then just pop it straight onto the GPIO.

Dimensions: 56.5x86x10mm (WxHxD, depth includes header and display).

 

Software

We've put together a one-line-installer to configure your Pi properly for HyperPixel and to enable the touch screen on the touch version. Note that you'll need another display, keyboard, and mouse to install the software, or you could do it remotely over SSH if you follow our guide on how to set your Pi up headlessly.

Find the GitHub repository here: https://github.com/pimoroni/hyperpixel

Our software does not support Raspbian Wheezy.

 

※ 공급 제조사는 재고 사정에 따라 동일 사양의 대체상품으로 공급될 수 있습니다.
※ 상기 제품에 첨부된 데이타시트는 참고사항입니다.데이타시트에 표기된 내용에 대하여 본사는 어떠한 기술적인 문의 및 발생하는 문제에 대한 법적인 책임을 지지는 않습니다. 
※ 사용자께서는 사용 전 반드시 제품에 대한 테스트 및 확인 절차 후 사용하시기 바랍니다

상세정보 배송/취소/교환안내 이용후기 상품Q&A