감추기
MCU상반기결산
홈 > 아두이노 > 아두이노 쉴드

아두이노 카메라 3.2인치 LCD 쉴드 + 2MP 카메라 모듈 Arducam-LF Rev.C+ Camera module + 3.2 inch LCD [B0052+B0011]
Arduino를 위한 범용 카메라 제어 보드 / RAW, RGB, YUV, JPEG와 같은 다양한 포맷의 0.3MP에서 5MP까지의 다양한 카메라 모듈을 지원
판매가격 : 77,000
적립금 :770
상품상태 :신상품
제품코드 :1383780
제조사 :ArduCAM
출시일 :2018-06-20
주의 :※ 해외 수입 제품 특성상 재고가 없을시 납기가 약 2주 소요될 수 있습니다.
구매수량 :
총 금액 :
MCU이용 꿀팁

12,500원
9,200원
18,000원
7,810원
84,600원
39,600원
25,300원
9,900원
14,630원
12,100원
상세정보 배송/취소/교환안내 이용후기 상품Q&A
아두이노 카메라 3.2인치 LCD 쉴드 + 2MP 카메라 모듈 Arducam-LF Rev.C+ Camera module + 3.2 inch LCD for arduino UNO MEGA2560 DUE [B0052+B0011]

Features

ArduCAM series camera shield is a universal camera control board for Arduino. It hides the complex nature of the camera and provides the easy to use camera control interface as well as the ready to use software source code library and demo code. The ArduCAM supports variety camera modules from 0.3MP to 5MP with different format like RAW, RGB, YUV, JPEG and can be well mated with standard Arduino boards.

ArduCAM Rev.C+ is the latest revision of ArduCAM shields, it offers the improved performance and enhanced functions than the previous revisions. It can capture maxim 5MP JPEG images, which makes it to be the ideal solution for IoT applications.

The ArduCAM is designed for Arduino but not limited to Arduino, it can be used in any platforms like Arduino, Raspberry Pi, Maple, Chipkit, Beaglebone black, as long as they have the SPI and I2C interface. User can port the current Arduino library to other platforms with less effort.

  • Support 0.3MP~5MP camera modules, see Table 1
  • 3.2 inch TFT LCD with touch screen
  • Build in SD/TF card socket
  • Support JPEG compression mode, single and multiple shoot mode, one time capture multiple read operation, burst read operation, low power mode and etc.
  • Support almost all microcontroller platform,
  • Provide open source code library, please visit github.org/arducam
  • All ArduCAM’s IO ports are 5V/3.3V tolerant
  • Well mated with standard Arduino boards
  • Power supply 5V/50mA (Not including Camera Module)
  • SPI speed: 8MHz
  • Frame buffer: 512KB
  • Format support: RAW,YUV,RGB,JPEG
  • Weight:50g
  • 3.2' TFT LCD with touch screen
  • SD/TF card socket
  • Resolution support:0.3MP~5MP
  • Size: 99 x 59mm
  • Temperature: -10°C~+55°C

Package Including:

  • 1pcs Arducam LF Shield V2 + Camera Module + 3.2 Inch LCD for Arduino UNO Mega2560 DUE
  • 1pcs OV2640 Camera module

ResolutionSensor VendorCamera ModuleManufacture
0.3MPOmnivisionOV7660 / OV7670 / OV7675 / OV7725ArduCAM
0.3MPAptinaMT9V111ArduCAM
1.3MPAptinaMT9M112 / MT9M001ArduCAM
2MPOmnivisionOV2640ArduCAM
2MPAptinaMT9D111 / MT9D112ArduCAM
3MPOmnivisionOV3640ArduCAM
3MPAptinaMT9T112ArduCAM
5MPOmnivisionOV5640 / OV5642ArduCAM

사용자 매뉴얼하드웨어 어플리케이션소프트웨어 어플리케이션

 

Pin Out

 

Block Diagram

Figure 3 shows the block diagram of ArduCAM shield which is composed by the camera module, LCD screen and an ArduChip. The camera module is changeable. The ArduChip uses ArduCAM proprietary third generation camera controller technology which handles the complex camera, memory, LCD and user interface hardware timing and provides a user friendly SPI interface.

 

 

Functions

  • Single Capture Mode

Single capture mode is the default capture mode of the camera. After issuing a capture command via SPI port, the ArduCAM will wait for a new frame and buffer the one entire image data to the frame buffer, and then assert the completion flag bit in the register. User only needs to poll the flag bit from the register to check out if the capture is done.

  • Multiple Capture Mode

Multiple capture mode is advanced capture mode. By setting the number of frames in the capture register, the ArduCAM will capture consequent frames after issuing capture command. Note that number of frames should be set properly and make sure do not exceed the maximum memory space.

  • JPEG Compression

The JPEG compression function is implemented in the image sensor. With proper register settings to the sensor, user can get different resolution with JPEG image stream output. It is recommended to use JPEG output to get higher resolution than RGB mode, due to the limitation of frame buffer.

  • Normal Read and Burst Read Operation

Normal read operation reads each image data by sending a read command in one SPI read operation cycle. While burst read operation only need to send a read command then read multiple image data in one SPI read operation cycle. It is recommended to use burst read operation to get better throughput performance.

  • Rewind Read Operation

Sometimes user wants to read the same frame of image data multiple times for processing, the rewind read operation is designed for this purpose. By resetting the read pointer to the beginning of the image data, user can read the same image data from the start point again.

  • Low Power Mode

Some battery power device need save power when in the idle status, the ArduCAM offers the low power mode to reduce power consumption, by shutdown the sensor and memory circuits.

  • Image Sensor Control

Image sensor control function is implemented in the image sensor. By setting proper set of register settings, user can control the exposure, white balance, brightness, contrast, color saturation and etc.

More technical information about ArduCAM shield, please read ArduCAM user guide,  hardware Application Note and software Application Note for detail.

 

 


※ 공급 제조사는 재고 사정에 따라 동일 사양의 대체상품으로 공급될 수 있습니다.
※ 상기 제품에 첨부된 데이타시트는 참고사항입니다.데이타시트에 표기된 내용에 대하여 본사는 어떠한 기술적인 문의 및 발생하는 문제에 대한 법적인 책임을 지지는 않습니다. 
※ 사용자께서는 사용 전 반드시 제품에 대한 테스트 및 확인 절차 후 사용하시기 바랍니다

상세정보 배송/취소/교환안내 이용후기 상품Q&A