감추기
크리스마스MCU
홈 > MCU보드 > AVR > 기타

Adafruit Feather M0 Express - Designed for CircuitPython - ATSAMD21 Cortex M0 [ada-3403]
피더 M0 익스프레스 버전 / Arduino Zero 에서 사용된 것과 동일한 48MHz 및 3.3V 로직으로 클럭된 ATSAMD21G18 ARM Cortex M0 + 프로세서
판매가격 : 31,900
적립금 :319
상품상태 :신상품
제품코드 :1378369
제조사 :adafruit
브랜드 :adafruit [브랜드바로가기]
출시일 :2018-08-06
구매수량 :
총 금액 :
MCU이용 꿀팁

15,950원
44,000원
33,600원
24,200원
17,600원
24,200원
14,300원
20,900원
15,900원
14,300원
상세정보 배송/취소/교환안내 이용후기 상품Q&A
Adafruit Feather M0 Express - Designed for CircuitPython - ATSAMD21 Cortex M0 [ada-3403]

Features


We love all our Feathers equally, but this Feather is very special. It's our first Feather that is specifically designed for use with CircuitPython! CircuitPython is our beginner-oriented flavor of MicroPython - and as the name hints at, its a small but full-featured version of the popular Python programming language specifically for use with circuitry and electronics.

Please note, CircuitPython does not come preloaded. See the full guide linked below for instructions on installing it.

That doesn't mean you cant also use it with Arduino IDE! At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0+ processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.

Here's some handy specs!

  • Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in
  • Light as a (large?) feather - 5 grams
  • ATSAMD21G18 @ 48MHz with 3.3V logic/power
  • 256KB of FLASH + 32KB of RAM
  • No EEPROM
  • 32.768 KHz crystal for clock generation & RTC
  • 3.3V regulator with 500mA peak current output
  • USB native support, comes with USB bootloader and serial port debugging
  • You also get tons of pins - 20 GPIO pins
  • Hardware Serial, hardware I2C, hardware SPI support
  • PWM outputs on all pins
  • 6 x 12-bit analog inputs
  • 1 x 10-bit analog ouput (DAC)
  • Built in 100mA lipoly charger with charging status indicator LED
  • Pin #13 red LED for general purpose blinking
  • Power/enable pin
  • 4 mounting holes
  • Reset button

The Feather M0 Express uses the extra space left over to add a Mini NeoPixel2 MB SPI Flash storage and a little prototyping space. You can use the SPI Flash storage like a very tiny hard drive. When used in CircuitPython, the 2 MB flash acts as storage for all your scripts, libraries and files. When used in Arduino, you can read/write files to it, like a little datalogger or SD card, and then with our helper program, access the files over USB.

Easy reprogramming: the Feather M0 comes pre-loaded with the UF2 bootloader, which looks like a USB storage key. Simply drag firmware on to program, no special tools or drivers needed! It can be used to load up CircuitPython, PXT MakeCode or Arduino IDE (it is bossa-compatible)

Comes fully assembled and tested, with the UF2 USB bootloader. We also toss in some header so you can solder it in and plug into a solderless breadboard. 

Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!)

  • Product Dimensions: 51.0mm x 22.8mm x 7.3mm / 2.0" x 0.9" x 0.3"
  • Product Weight: 4.7g / 0.2oz
아케이드 버튼
컨트롤박스 만들기

 






※ 공급 제조사는 재고 사정에 따라 동일 사양의 대체상품으로 공급될 수 있습니다.
※ 상기 제품에 첨부된 데이타시트는 참고사항입니다.데이타시트에 표기된 내용에 대하여 본사는 어떠한 기술적인 문의 및 발생하는 문제에 대한 법적인 책임을 지지는 않습니다. 
※ 사용자께서는 사용 전 반드시 제품에 대한 테스트 및 확인 절차 후 사용하시기 바랍니다

상세정보 배송/취소/교환안내 이용후기 상품Q&A