감추기
위킷 브랜드 출시
홈 > 센서/모듈/키트 > 모터/기타 모듈

L298 듀얼 H-Bridge 모터드라이버 모듈 [RB-01C025]
판매가격 : 26,100
적립금 :0
상품상태 :신상품
제품코드 :9899915
원산지 :해외
제조사 :ALSROBOT
브랜드 :ALSROBOT [브랜드바로가기]
출시일 :2018-12-10
구매수량 :
제품상태 :
총 금액 :
MCU이용 꿀팁

6,820원
54,450원
8,360원
5,020원
14,520원
6,300원
11,700원
1,650원
6,740원
1,890원
상세정보 배송/취소/교환안내 이용후기 상품Q&A








LKV-HM3.0 dual H-bridge DC motor driver board using ST's L298N typical dual H-bridge DC motor driver IC, which can be used to drive DC motors or bipolar stepper motors. This driver board is small, light weight, but with a strong drive capability: 2A peak current and peak voltage of 46V.Although the chip with the automatic shut-off function when it is overheating , but installing the heat sink could make the chip temperature decreases, so that the drive performance is more stable.

Board has two current feedback detection interface to take power within the logic selects the terminal, four pull-up resistor selection terminal, 2-way and four-wire interfaces DC two-phase stepper motor interface, control motor direction indicator, four standard fixed mounting holes. This driver board could be used with smart programmable trolley, wheeled robots and variety of controllers.

Dual H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together,and the corresponding external terminal can be used for the connection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage.

Specifications:

    Driver: L298 Driver power supply: +5V~+46V Driver Io: 2A Logic power output Vss: +5~+7V (internal supply +5V) Logic current: 0~36mA Controlling level: Low -0.3V~1.5V, high: 2.3V~Vss Enable signal level: Low -0.3V~1.5V, high: 2.3V~Vss Max power: 25W (Temperature 75 cesus) Working temperature: -25C~+130C Dimension: 60mm*54mm Driver weight: 48g Other extensions: current probe, controlling direction indicator, pull-up resistor switch, logic part power supply

Features:

    Light weight, small dimension Super driver capacity FWD protection Heavy load Heat sink 2 current probe port Power selection switch 4 pull up resistor switch 2 DC motor/ 4 coil dual phrase stepper motor output Motor direction indication LED 4 standard mouting hole

Packing List:

    1x L298 Dual H-Bridge Motor Driver
※ 공급 제조사는 재고 사정에 따라 동일 사양의 대체상품으로 공급될 수 있습니다.
※ 상기 제품에 첨부된 데이타시트는 참고사항입니다.데이타시트에 표기된 내용에 대하여 본사는 어떠한 기술적인 문의 및 발생하는 문제에 대한 법적인 책임을 지지는 않습니다. 
※ 사용자께서는 사용 전 반드시 제품에 대한 테스트 및 확인 절차 후 사용하시기 바랍니다

상세정보 배송/취소/교환안내 이용후기 상품Q&A