감추기
MCU상반기결산
홈 > 라즈베리파이 > 확장보드

Adafruit Perma-Proto HAT for Pi Mini Kit - With EEPROM [ada-2314]
Pi A+, B+, or Pi 2 와 모두 호환됩니다. / 원하시는 실드를 만드실 수 있는 proto-type 의 실드입니다. / blank 24C32 I2C EEPROM 포함 제품 / 66mm x 57mm x 2mm
판매가격 : 10,030
적립금 :100
상품상태 :신상품
제품코드 :1260298
제조사 :adafruit
브랜드 :아다프루트 [브랜드바로가기]
출시일 :2018-02-07
구매수량 :
총 금액 :
MCU이용 꿀팁

10,560원
46,200원
36,000원
59,400원
33,000원
8,470원
16,500원
13,000원
51,500원
9,520원
상세정보 배송/취소/교환안내 이용후기 상품Q&A




Adafruit Perma-Proto HAT for Pi Mini Kit - With EEPROM [ada-2314]

Description

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit with EEPROM

To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards you're familiar. There's also long power strips for +3V, +5V and Ground connections to the Pi. Near the top we break out nearly every pin you could want to connect to the Pi (#26 didnt quite make the cut).

This is the fancier version of our Perma-Proto HAT. It comes with a printed circuit board and a single 2x20 GPIO Header for Raspberry Pi to put your Perma-Proto on top of your Raspberry Pi (like a nice little hat...) This version comes with a blank 24C32 I2C EEPROM soldered on and connected to the EEDAT/EECLK lines so you cannot 'stack' it with other HATs. However, you can program in the EEPROM to make a self-identifying setup using the Pi Foundations' HAT specs - please note the specifications are still under development.

You can customize your Perma-Proto setup using a standard 2x20 stacking header or extra tall 2x20 stacking header. You can also swap out the 2x20 header with a slim 2x20 type if you want it to sit closer to the Pi, or an extra tall one if you want it to sit above the USB/Ethernet ports.

A bit of light soldering is required to attach the header to the PCB but it's easy work.

This hat is only compatible with the Raspberry Pi A+, B+, or Pi 2! It will not work with the Raspberry Pi Model A or B.

Our initial version has the +3V and +5V markings in blue, and the GND markings in red, future orders will have these colors swapped to better match a solderless breadboard

 


TECHNICAL DETAILS

  • Header Dimensions: 5mm x 51mm x 12mm / 0.2" x 2" x 0.5"
  • PCB Dimensions: 66mm x 57mm x 2mm / 2.6" x 2.2" x 0.1"

 

※ 공급 제조사는 재고 사정에 따라 동일 사양의 대체상품으로 공급될 수 있습니다.
※ 상기 제품에 첨부된 데이타시트는 참고사항입니다.데이타시트에 표기된 내용에 대하여 본사는 어떠한 기술적인 문의 및 발생하는 문제에 대한 법적인 책임을 지지는 않습니다. 
※ 사용자께서는 사용 전 반드시 제품에 대한 테스트 및 확인 절차 후 사용하시기 바랍니다

상세정보 배송/취소/교환안내 이용후기 상품Q&A