감추기
MCU상반기결산
홈 > 라즈베리파이 > 확장보드

라즈베리파이 GPS 확장보드 Adafruit Ultimate GPS HAT for Raspberry Pi - Mini Kit ada-2324
라즈베리파이 호환 / GPS 모듈 / 66 channels / -165 dBm sensitivity / 10 Hz updates / 20mA 출력 /Built in Real Time Clock / 백업배터리 슬롯(CR1220) / 배터리 별매
판매가격 : 59,400
적립금 :594
상품상태 :신상품
제품코드 :1170705
제조사 :adafruit
브랜드 :아다프루트 [브랜드바로가기]
출시일 :2018-02-07
주의사항 :해외상품 - 상품 준비기간 약 일주일 소요됩니다.
구매수량 :
총 금액 :
MCU이용 꿀팁

51,500원
9,240원
50,160원
10,700원
46,200원
7,900원
8,710원
29,050원
46,200원
29,700원
상세정보 배송/취소/교환안내 이용후기 상품Q&A






 Adafruit Ultimate GPS HAT for Raspberry Pi A+/B+/Pi 2                 - Mini Kit [ada-2324]

Description

It's 10PM, do you know where your Raspberry Pi is? If you had this GPS HAT, you would! This new HAT from Adafruit adds our celebrated Ultimate GPS on it, so you can add precision time and location to your Raspberry Pi Model A+, B+, or Pi 2

Here's the low-down on the GPS module:

  • -165 dBm sensitivity, 10 Hz updates, 66 channels
  • Only 20mA current draw
  • Built in Real Time Clock (RTC) - slot in a CR1220 backup battery for 7-years or more of timekeeping even if the Raspberry Pi is off!
  • PPS output on fix, by default connected to pin #4
  • Internal patch antenna which works quite well when used outdoors + u.FL connector for external active antenna for when used indoors or in locations without a clear sky view
  • Fix status LED blinks to let you know when the GPS has determined the current coordinates

We spun up a HAT based on our Ultimate GPS, added a coin-cell holder for RTC usage, break-outs for all the Raspberry Pi's extra pins, and plenty of prototyping area for adding LEDs, sensors, and more.

Please note, this HAT takes over the Raspberry Pi's hardware UART to send/receive data to and from the GPS module. So, if you need to use the RX/TX pins with a console cable, you cannot also use this HAT. Instead, you'll have to use a composite or HDMI monitor and keyboard to log in, or use ssh to connect over the network to your Pi. Read up on our tutorial for more information on how to use this fine HAT

Comes as a fully assembled GPS + PCB and an additional 2x20 GPIO header. Some light soldering is required to attach the 2x20 GPIO header to the HAT but it's fast and easy for anyone with a soldering iron and solder. You can also swap the plain female header we have with a 'stacky' type that lets you plug in a hat or GPIO cable on top or a slim ultra-low-profile header.

To make air-shipping eaiser, this HAT does not come with a 12mm coin battery! A CR1220 will let you use the real-time-clock capability of the GPS HAT, you can pick one up locally or order one from us.


 

Details

  • Dimensions w/ components: 65mm x 56mm x 7mm / 2.6" x 2.2" x 0.3"
 

※ 공급 제조사는 재고 사정에 따라 동일 사양의 대체상품으로 공급될 수 있습니다.
※ 상기 제품에 첨부된 데이타시트는 참고사항입니다.데이타시트에 표기된 내용에 대하여 본사는 어떠한 기술적인 문의 및 발생하는 문제에 대한 법적인 책임을 지지는 않습니다. 
※ 사용자께서는 사용 전 반드시 제품에 대한 테스트 및 확인 절차 후 사용하시기 바랍니다

상세정보 배송/취소/교환안내 이용후기 상품Q&A